cbb/DCU_APP
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
5fd986299ce60493843ea40c1a392fc728f0806f
DCU_APP/GD32E508_DCU_APP/GD32E508_DCU_APP.cproject.yml
T
cbb 959e2aef6e feat(comm): 1.6.14~1.6.20 —— CAN-FD 数据段 5M、批量区改定长覆盖窗口(输入 PDO 496→600)、drop 口径修复、差分写仪表 
1.6.14 CAN-FD 数据段 2Mbps→5Mbps：CONFIG_CAN_DATA_PRESCALER 9→3、BS1 3→4TQ
  (90MHz/(3×6TQ)，采样点 80%→83.3%)，仲裁段仍 1M。TDC filter/offset 维持 4 不做
  等比缩放（TDCMOD=CALC_AND_OFFSET 下硬件已自动测回路延时；放到 12 会让本节点回采
  错开约 6 个数据位，自发热帧被判错误帧）。配套电机 APP/BOOT data_prescaler=2。

1.6.15 段4 批量接收由"环形队列 + 变长紧排排空"改为 5×44B 定长覆盖窗口，输入 PDO
  496→600(75×64bit)，段5 诊断区 484→584。动机两条：现场 4000 帧/s 超旧容量 3 帧/拍
  恒丢 1 帧；更关键是排空赤字把队列长期压在饱和态，而 1.6.9~1.6.13 追的错标/拼接竞态
  正是饱和态喂出来的（判满用的 tail 滞后→生产者写进消费者刚读过的槽）。定长消灭
  tail/判满/pending，边界越界写在结构上不可能再犯。每槽带 u32 seqlock：buildInput 在
  PDI_Isr(preempt=0) 抢占主循环写侧，无它则主站会拿到"新 ID + 旧数据"拼出的假帧。
  out+in=984 ≤ 1024 硬上限，DPRAM 留 120B。语义变更：批量区从"不丢的事件流"变"最近
  N 帧窗口"，去重与丢帧判据移交主站按 seq 归一。三端同步 size.h/bridge/dc_app/
  gen_eeprom/DCU_ESI.xml，必须重烧固件 + 烧 EEPROM + 断电冷启动，只烧一边 SAFEOP 报
  AL 0x001A/0x0011。

1.6.16 段1/段3 快照 drop 计数口径修复（纯判据，PDO 布局逐字节不动）：旧判据
  s_rxValid 置位后永不清零 ⇒ 开机首帧后每帧都算丢弃，drop ≡ rx−1，是零灵敏度假仪表
  且把网页状态栏刷成 ERR。新增 s_rxPublished，判据改 s_rxValid && !s_rxPublished。

1.6.17~19 [DIFF-STATS] 差分写取证仪表，零行为变更，只加 0x2000 sub13..23(11 个只读
  UINT32) ⇒ 不动 PDO 长度/映射，无需重生成 SII。实测：每拍 27.4% 字节真变化(164B)、
  run 峰值 12~13、段2 占变化量 ~53%、段4 ~25%。
  1.6.19 推翻 1.6.18 的自我诊断：比对开销虚报不是 -Oz 把 memcpy 编成调用（手拼移位
  反而 21.3µs→41µs），真根因是 alignas(4) 到 const uint8_t* 形参处丢失，优化器无法
  证明 4 字节对齐。__builtin_assume_aligned + memcpy 后循环体缩成 ldr/ldr/cmp/bne、
  bl 归零。教训：测量工具自身的开销会直接变成结论。

1.6.20 基线对照版（当前提交状态 CONFIG_ECAT_DIFF_STATS=0）：同工况(电机在线无指令)
  实测 load 49.1% vs 仪表开的 51.6% ⇒ 仪表自身成本 2.4 个点，差分改造收益 = 0。
  按实测变化量推算 A1(段粒度条件写) 只值约 1 点(段2/段4 每拍都变，必然整块重写)，
  仅 A2(8B 块粒度 + run 上限退化为整写) 有空间 —— 推算值，未做 A/B 实测不作为结论。
2026-09-09 03:04:53 +08:00

179 lines
6.6 KiB
YAML
Raw Blame History

This file contains ambiguous Unicode characters
This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
# A project translates into one executable or library.
project:
groups:
- group: Source Files
files:
- file: ./main.h
- file: ./main.cpp
- group: sys
files:
- file: ./sys/initial.h
- file: ./sys/initial.cpp
- file: ./sys/systick.h
- file: ./sys/systick.cpp
- file: ./sys/task_manager.h
- file: ./sys/task_manager.cpp
- file: ./sys/task_runner.h
- file: ./sys/task_runner.cpp
- file: ./sys/cpu_load.h
- file: ./sys/cpu_load.cpp
- file: ./sys/ota_boot_request.h
- file: ./sys/ota_boot_request.cpp
- file: ./sys/aes128.h
- file: ./sys/aes128.cpp
- file: ./sys/motor_ota_relay.h
- file: ./sys/motor_ota_relay.cpp
- file: ./sys/hardfault.cpp
- file: ./sys/cpp_stubs.cpp
- file: ./sys/config.h
- group: device
files:
- file: ./device/adc.h
- file: ./device/adc.cpp
- file: ./device/canfd.h
- file: ./device/canfd.cpp
- file: ./device/timer.h
- file: ./device/timer.cpp
- file: ./device/usart0.h
- file: ./device/usart0.cpp
- file: ./device/watchdog.h
- file: ./device/watchdog.cpp
- file: ./device/motor_state.h
- file: ./device/motor_state.cpp
- file: ./device/motor_version.h
- file: ./device/motor_version.cpp
# GigaDevice DFP 未把 EXMC 注册为 CMSIS 组件（仅有 FMC=片内 Flash），
# 但外设源文件存在于 Pack；LAN9252 并行总线需要 EXMC，故本地编入。
- group: device_exmc
files:
- file: ./RTE/Device/GD32E508VE/gd32e50x_exmc.c
- file: ./RTE/Device/GD32E508VE/gd32e50x_exmc.h
- group: device/spi
files:
- file: ./device/spi/app_spi_command.h
- file: ./device/spi/app_spi_command.cpp
- file: ./device/spi/spi_command_handler.h
- file: ./device/spi/app_spi_command_defs.h
- file: ./device/spi/app_spi_cmd_boot_request.cpp
- file: ./device/spi/app_spi_cmd_ota_wait.cpp
- file: ./device/spi/app_spi_cmd_ping.cpp
- file: ./device/spi/app_spi_cmd_init_status.cpp
- file: ./device/spi/app_spi_cmd_can_bridge.cpp
- file: ./device/spi/app_spi_cmd_can_burst.cpp
- file: ./device/spi/app_spi_cmd_can_feedback.cpp
- file: ./device/spi/app_spi_cmd_id_snapshot.cpp
- file: ./device/spi/app_spi_cmd_adc_feedback.cpp
- file: ./device/spi/app_spi_cmd_motor_state.cpp
- file: ./device/spi/app_spi_cmd_motor_version.cpp
- file: ./device/spi/app_spi_cmd_motor_ota.cpp
- file: ./device/spi/app_spi_cmd_exmc_diag.cpp
- group: spi_link
files:
- file: ../../spi_link/spi_link_v2.cpp
- group: comm
files:
- file: ./comm/esc_exmc_bus.h
- file: ./comm/esc_exmc_bus.cpp
- file: ./comm/esc_lan9252.h
- file: ./comm/esc_lan9252.cpp
- file: ./comm/ethercat_slave.h
- file: ./comm/ethercat_slave.cpp
- file: ./comm/ethercat_sync.h
- file: ./comm/ethercat_sync.cpp
- file: ./comm/ethercat_can_bridge.h
- file: ./comm/ethercat_can_bridge.cpp
- file: ./comm/ethercat_pdo.h
- file: ./comm/ethercat_pdo.cpp
# [DIFF-STATS] 临时仪表：差分写取证，删除时连同本两行与 comm/ethercat_diff_stats.* 一并移除
- file: ./comm/ethercat_diff_stats.h
- file: ./comm/ethercat_diff_stats.cpp
- group: comm/ssc
files:
- file: ./comm/ssc/inc/ecatslv.h
- file: ./comm/ssc/inc/ecatappl.h
- file: ./comm/ssc/inc/mailbox.h
- file: ./comm/ssc/inc/ecatcoe.h
- file: ./comm/ssc/inc/sdoserv.h
- file: ./comm/ssc/inc/objdef.h
- file: ./comm/ssc/inc/coeappl.h
- file: ./comm/ssc/inc/esc.h
- file: ./comm/ssc/inc/applInterface.h
- file: ./comm/ssc/inc/el9800hw.h
- file: ./comm/ssc/src/ecatslv.c
- file: ./comm/ssc/src/ecatappl.c
- file: ./comm/ssc/src/mailbox.c
- file: ./comm/ssc/src/ecatcoe.c
- file: ./comm/ssc/src/sdoserv.c
- file: ./comm/ssc/src/objdef.c
- file: ./comm/ssc/src/coeappl.c
- file: ./comm/ssc/port/hw_gd32exmc.cpp
- file: ./comm/ssc/port/dc_app.c
- file: ./comm/ssc/port/dc_app.h
- file: ./comm/ssc/port/ecat_def.h
# List components to use for your application.
# A software component is a re-usable unit that may be configurable.
components:
- component: ARM::CMSIS:CORE
- component: Device:Startup
- component: Device:GD32E50x_StdPeripherals:ADC
- component: Device:GD32E50x_StdPeripherals:CAN
- component: Device:GD32E50x_StdPeripherals:CRC
- component: Device:GD32E50x_StdPeripherals:DBG
- component: Device:GD32E50x_StdPeripherals:DMA
- component: Device:GD32E50x_StdPeripherals:EXTI
- component: Device:GD32E50x_StdPeripherals:FMC
- component: Device:GD32E50x_StdPeripherals:GPIO
- component: Device:GD32E50x_StdPeripherals:MISC
- component: Device:GD32E50x_StdPeripherals:PMU
- component: Device:GD32E50x_StdPeripherals:RCU
- component: Device:GD32E50x_StdPeripherals:SPI_I2S
- component: Device:GD32E50x_StdPeripherals:TIMER
- component: Device:GD32E50x_StdPeripherals:USART
- component: Device:GD32E50x_libopt
- component: Device:GD32E50x_StdPeripherals:FWDGT
# List executable file formats to be generated.
output:
type:
- elf
- hex
- map
misc:
- for-compiler: AC6
C-CPP:
- -DGD32E508
- -DGD32E50X
- -DHXTAL_VALUE=8000000U
- -gdwarf-5
- -D__MICROLIB
- -fshort-enums
- -fshort-wchar
# EXMC 未作为 CMSIS 组件分发；头文件在 RTE 本地目录
- -IRTE/Device/GD32E508VE
- -Wno-register
- -IG:/Robot_v2/DCU/spi_link
C:
- -std=gnu11
CPP:
- -std=gnu++17
# 全工程零使用 RTTI/异常（grep 验证），关闭以剥离 libcppabi 运行时（约 2.5 KB Flash）
- -fno-rtti
- -fno-exceptions
ASM:
- -DGD32E508
- -DGD32E50X
- -DHXTAL_VALUE=8000000U
- -gdwarf-5
- -D__MICROLIB
# 启动文件经 legacy armasm 汇编：消 armclang 驱动"参数未使用"告警 + armasm 弃用告警(A1950W)
- -Wno-unused-command-line-argument
- -Wa,armasm,--diag_suppress=A1950W
Link:
- --library_type=microlib
- --entry=Reset_Handler
# 输出未引用段与总量报告，用于 Flash 尺寸归因
- --info=unused,totals
Reference in New Issue View Git Blame Copy Permalink