DCU_APP/GD32E508_DCU_APP/comm/esc_exmc_bus.cpp

/**
 * @file esc_exmc_bus.cpp
 * @brief LAN9252 ESC 的 EXMC 16-bit 并行总线驱动实现。
 *
 * 使用 GigaDevice gd32e50x_exmc 标准库。
 * 注意：DFP 只把 FMC 注册为 CMSIS 组件，EXMC 未进组件列表；
 * 源文件放在 RTE/Device/... 并由 cproject group device_exmc 本地编译。
 */
#include "comm/esc_exmc_bus.h"
#include "comm/ethercat_sync.h"
#include "sys/config.h"
#include "device/watchdog.h"
#include <stdio.h>
#include "RTE_Components.h"
#include CMSIS_device_header

extern "C" {
#include "gd32e50x_exmc.h" /* RTE/Device/GD32E508VE 或 -I 同目录 */
#include "gd32e50x_gpio.h"
#include "gd32e50x_rcu.h"
}

/* 内存映射访问宏:基址 + CPU 字节偏移。
 * 注意 EXMC 16-bit 模式地址左移 1 位(用户手册 p869:HADDR[25:1]→EXMC_A[24:0]):
 * EXMC_A16(PD11) 引脚对应偏移 bit17=0x20000,EXMC_A17(PD12) 对应 bit18=0x40000,
 * 即 1<<16 的 CPU 偏移驱动的是 A15 引脚而非 A16。 */
#define ESC_EXMC_REG16(offset)                                                 \
  (*(volatile uint16_t *)(CONFIG_ESC_EXMC_BASE_ADDR + (offset)))

/* ========================================================================
 * GPIO 位拍(bit-bang)辅助函数 —— 完全绕过 EXMC 外设,
 * 用普通 GPIO 手动产生 LAN9252 HBI 时序,用于判定"芯片是否活着"。
 * 数据线物理映射:D0=PD14 D1=PD15 D2=PD0 D3=PD1 D4..D12=PE7..PE15
 *                 D13=PD8 D14=PD9 D15=PD10
 * 控制线:CS#=PD7(NE0)  RD#=PD4(NOE)  WR#=PD5(NWE)  A1=PD11  A2=PD12
 * ======================================================================== */
namespace {

/* 通断测试模式状态(提前声明供 diagDump() 检查) */
static bool s_continuityActive = false;

/* GPIOD/GPIOE 上属于数据总线的引脚掩码 */
constexpr uint32_t kDataMaskD =
    (1U << 0) | (1U << 1) | (1U << 8) | (1U << 9) | (1U << 10) | (1U << 14) |
    (1U << 15);
constexpr uint32_t kDataMaskE = 0xFF80U; /* PE7..PE15 */

constexpr uint32_t kPinCs = 7U;  /* PD7  */
constexpr uint32_t kPinRd = 4U;  /* PD4  */
constexpr uint32_t kPinWr = 5U;  /* PD5  */
constexpr uint32_t kPinA1 = 11U; /* PD11 */
constexpr uint32_t kPinA2 = 12U; /* PD12 */

/* bbDelay/bbReadData 仅被 diagDump 使用，随之一起门控，避免默认关闭时
 * 触发 -Wunused-function；bbDriveData 被 continuityDrive 复用，保持常开。 */
#if CONFIG_ESC_EXMC_DIAG
void bbDelay() {
  for (volatile uint32_t i = 0U; i < 3000U; i++) {
  } /* ~40-80us @180MHz,远大于 HBI 时序要求 */
}

uint16_t bbReadData() {
  uint32_t d = GPIO_ISTAT(GPIOD);
  uint32_t e = GPIO_ISTAT(GPIOE);
  uint16_t v = 0U;
  if (d & (1U << 14)) v |= (uint16_t)(1U << 0);  /* D0  */
  if (d & (1U << 15)) v |= (uint16_t)(1U << 1);  /* D1  */
  if (d & (1U << 0))  v |= (uint16_t)(1U << 2);  /* D2  */
  if (d & (1U << 1))  v |= (uint16_t)(1U << 3);  /* D3  */
  if (e & (1U << 7))  v |= (uint16_t)(1U << 4);  /* D4  */
  if (e & (1U << 8))  v |= (uint16_t)(1U << 5);  /* D5  */
  if (e & (1U << 9))  v |= (uint16_t)(1U << 6);  /* D6  */
  if (e & (1U << 10)) v |= (uint16_t)(1U << 7);  /* D7  */
  if (e & (1U << 11)) v |= (uint16_t)(1U << 8);  /* D8  */
  if (e & (1U << 12)) v |= (uint16_t)(1U << 9);  /* D9  */
  if (e & (1U << 13)) v |= (uint16_t)(1U << 10); /* D10 */
  if (e & (1U << 14)) v |= (uint16_t)(1U << 11); /* D11 */
  if (e & (1U << 15)) v |= (uint16_t)(1U << 12); /* D12 */
  if (d & (1U << 8))  v |= (uint16_t)(1U << 13); /* D13 */
  if (d & (1U << 9))  v |= (uint16_t)(1U << 14); /* D14 */
  if (d & (1U << 10)) v |= (uint16_t)(1U << 15); /* D15 */
  return v;
}
#endif /* CONFIG_ESC_EXMC_DIAG (bbDelay + bbReadData) */

void bbDriveData(uint16_t v) {
  uint32_t dset = 0U, dclr = 0U, eset = 0U, eclr = 0U;
  /* GPIOD 数据位 */
  const uint32_t dpins[7] = {14U, 15U, 0U, 1U, 8U, 9U, 10U};
  const int dbits[7] = {0, 1, 2, 3, 13, 14, 15};
  for (int i = 0; i < 7; ++i) {
    if (v & (1U << dbits[i])) dset |= (1U << dpins[i]);
    else                      dclr |= (1U << dpins[i]);
  }
  /* GPIOE 数据位:D4..D12 = PE7..PE15 = 数据位 4..12 */
  for (int bit = 4; bit <= 12; ++bit) {
    uint32_t pin = (uint32_t)(bit + 3); /* bit4->PE7 ... bit12->PE15 */
    if (v & (1U << bit)) eset |= (1U << pin);
    else                 eclr |= (1U << pin);
  }
  if (dset) GPIO_BOP(GPIOD) = dset;
  if (dclr) GPIO_BC(GPIOD) = dclr;
  if (eset) GPIO_BOP(GPIOE) = eset;
  if (eclr) GPIO_BC(GPIOE) = eclr;
}

} /* anonymous namespace */

bool EscExmcBus::s_ok = false;
bool EscExmcBus::init() {
  s_ok = false;
  ECAT_LOGI("[ECAT][EXMC] init: enable RCU clocks\r\n");
  rcu_periph_clock_enable(RCU_GPIOD);
  rcu_periph_clock_enable(RCU_GPIOE);
  rcu_periph_clock_enable(RCU_AF);
  rcu_periph_clock_enable(RCU_EXMC);
  /* 先 deinit 再 init。BOOT 跳转前 exmc_norsram_disable + 关时钟,
   * SNCTL/SNTCFG 仍留着 BOOT 的配置;APP 若只 enable+init 可能叠在残留位上。
   * deinit 把 Region0 打回复位默认,再按下面参数重铺。 */
  exmc_norsram_deinit(CONFIG_ESC_EXMC_BANK_NOR_SRAM_REGION0);
  /* 配置 16-bit 数据线 D0-D15 为 AF 推挽 */
  gpio_init(CONFIG_EXMC_D0_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D0_PIN);
  gpio_init(CONFIG_EXMC_D1_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D1_PIN);
  gpio_init(CONFIG_EXMC_D2_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D2_PIN);
  gpio_init(CONFIG_EXMC_D3_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D3_PIN);
  gpio_init(CONFIG_EXMC_D4_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D4_PIN);
  gpio_init(CONFIG_EXMC_D5_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D5_PIN);
  gpio_init(CONFIG_EXMC_D6_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D6_PIN);
  gpio_init(CONFIG_EXMC_D7_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D7_PIN);
  gpio_init(CONFIG_EXMC_D8_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D8_PIN);
  gpio_init(CONFIG_EXMC_D9_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D9_PIN);
  gpio_init(CONFIG_EXMC_D10_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D10_PIN);
  gpio_init(CONFIG_EXMC_D11_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D11_PIN);
  gpio_init(CONFIG_EXMC_D12_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D12_PIN);
  gpio_init(CONFIG_EXMC_D13_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D13_PIN);
  gpio_init(CONFIG_EXMC_D14_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D14_PIN);
  gpio_init(CONFIG_EXMC_D15_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_D15_PIN);

  /* 控制线:A16 / A17 / NOE / NWE / NE0
   * A17(PD12) → LAN9252 A2 (Pin 29,IDX/DATA 选择);A16(PD11) → LAN9252 A1 (Pin 25)。
   * 注意 EXMC 16-bit 模式地址左移 1 位:HBI_DATA_0 的 CPU 偏移是 0x40000/0x60000,
   * 见 esc_lan9252.cpp 头注释。 */
  gpio_init(CONFIG_EXMC_A16_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_A16_PIN);
  gpio_init(CONFIG_EXMC_A17_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_A17_PIN);
  gpio_init(CONFIG_EXMC_NOE_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_NOE_PIN);
  gpio_init(CONFIG_EXMC_NWE_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_NWE_PIN);
  gpio_init(CONFIG_EXMC_NE0_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ,
            CONFIG_EXMC_NE0_PIN);
  ECAT_LOGI(
      "[ECAT][EXMC] init: GPIO configured (D0-D15/A16/A17/NOE/NWE/NE0)\r\n");

  /*
   * EXMC NOR/SRAM Region0：16-bit、非复用、异步写。
   * 注意：GD32E508Vx (LQFP100) 只有 NE0 (PD7) 一个 NOR/SRAM 片选引脚，
   *       NE0 归属 Region0 (0x60000000, SNCTL0)，必须用 Region0。
   * 时序（AHB=180MHz，1 HCLK ≈ 5.56ns）：
   *   LAN9252 HBI 最小读/写周期约 100ns → data_setup ≥ 18 HCLK。
   * asyn_* 字段单位为 HCLK 计数（库文档范围
   * address_setup 1..16，data_setup 2..256）。
   */
  exmc_norsram_parameter_struct norsram_init;
  exmc_norsram_timing_parameter_struct rw_timing;
  exmc_norsram_timing_parameter_struct wr_timing;

  norsram_init.read_write_timing = &rw_timing;
  norsram_init.write_timing = &wr_timing;
  exmc_norsram_struct_para_init(&norsram_init);

  norsram_init.norsram_region = CONFIG_ESC_EXMC_BANK_NOR_SRAM_REGION0;
  norsram_init.write_mode = EXMC_ASYN_WRITE;
  norsram_init.extended_mode = DISABLE;
  norsram_init.asyn_wait = DISABLE;
  norsram_init.nwait_signal = DISABLE;
  norsram_init.memory_write = ENABLE;
  norsram_init.nwait_config = EXMC_NWAIT_CONFIG_BEFORE;
  norsram_init.wrap_burst_mode = DISABLE;
  norsram_init.nwait_polarity = EXMC_NWAIT_POLARITY_LOW;
  norsram_init.burst_mode = DISABLE;
  norsram_init.databus_width = EXMC_NOR_DATABUS_WIDTH_16B;
  norsram_init.memory_type = EXMC_MEMORY_TYPE_SRAM;
  norsram_init.address_data_mux = DISABLE;

  /* 读/写共用时序（非 extended mode）。时序余量按 DS 表 9-4/9-5 独立核算,见下方 BUSLAT。 */
  rw_timing.asyn_access_mode = EXMC_ACCESS_MODE_A;
  rw_timing.syn_data_latency = EXMC_DATALAT_2_CLK;
  rw_timing.syn_clk_division = EXMC_SYN_CLOCK_RATIO_DISABLE;
  /* BUSLAT: 4。DS 表 9-4/9-5 要求 trdrd/twrwr/twrrd ≥ 13ns,
   * 该间隔由 EXMC 在两次访问之间插入的总线空闲期承担 = (1 固有 + BUSLAT) HCLK。
   * BUSLAT=1 → 2 HCLK ≈ 11.1ns,低于 13ns 下限,仅靠 AHB 取指间隙偶然兜底:
   * 常温刚好可用,温度升高(传播延迟增大)/电压下降(驱动减弱)即越界,表现为
   * 偶发读到 0xFFFF 或错值。
   * BUSLAT=4 → 5 HCLK ≈ 27.8ns,余量 2.1 倍,覆盖全温区与电压波动。
   * 代价:每次 HBI 访问多 3 HCLK(16.7ns)。满载 1024B 过程数据按每 DWORD
   * 两次 16-bit 访问计,增加约 256×2×16.7ns ≈ 8.6us,相对原 218us 增幅 3.9%,
   * 4ms 周期占用从 5.4% 升至 5.7%,无实质影响。 */
  rw_timing.bus_latency = 4U;
  rw_timing.asyn_address_setuptime = 4U; /* ~22ns。DS 表9-4/9-5: trdrd/twrwr/twrrd
                                              ≥13ns——选通间隔=ADDSET 相,2 HCLK≈11.1ns
                                              不达标(仅靠 AHB 间隙兜底),4 HCLK 稳过 */
  rw_timing.asyn_address_holdtime = 2U;  /* min 2,DS tah≥0 */
  rw_timing.asyn_data_setuptime = 20U;   /* ~111ns ≥ 100ns HBI */

  wr_timing = rw_timing;

  ECAT_LOGI("[ECAT][EXMC] init: applying NOR/SRAM Region0 params (16b, async, "
            "ADDSET=%u AHLD=%u DSET=%u BUSLAT=%u HCLK)\r\n",
            (unsigned)rw_timing.asyn_address_setuptime,
            (unsigned)rw_timing.asyn_address_holdtime,
            (unsigned)rw_timing.asyn_data_setuptime,
            (unsigned)rw_timing.bus_latency);

  exmc_norsram_init(&norsram_init);
    exmc_norsram_enable(CONFIG_ESC_EXMC_BANK_NOR_SRAM_REGION0);

    /* === 清除 reserved bit 7 ===
     * 现象:exmc_norsram_init 后 EXMC_SNCTL0=0x00001091,bit 7(reserved)=1。
     *       DFP 复位值 0x000030DB 的 bit 7=1,可能被硬件保留或导致未定义行为。
     *       NRW(bits 4-5)=01 已经是 16-bit,无需修改。
     * 修复:清除 bit 7,保持其他位不变。 */
    uint32_t snctl_before = EXMC_SNCTL0;
    EXMC_SNCTL0 = snctl_before & ~BIT(7);
    uint32_t snctl_after = EXMC_SNCTL0;
    ECAT_LOGI("[ECAT][EXMC] init: SNCTL0 fix: before=0x%08lX after=0x%08lX (bit7 reserved cleared)\r\n",
           (unsigned long)snctl_before, (unsigned long)snctl_after);

    /* 时序寄存器回读:确认写入的 BUSLAT 真正落到硬件。
     * SNTCFG0 位域: [3:0]=ASET-1 [7:4]=AHLD-1 [15:8]=DSET-1 [19:16]=BUSLAT-1。
     * 期望 ASET=4/AHLD=2/DSET=20/BUSLAT=4 → 0x0313_0000|... 逐字段解码打印,
     * 避免只看整字导致的位域误读;BUSLAT 实际值 <4 说明库或硬件截断,须立即排查。 */
    {
      const uint32_t tcfg = EXMC_SNTCFG0;
      const unsigned aset   = (unsigned)((tcfg & EXMC_SNTCFG_ASET) >> 0) + 1U;
      const unsigned ahld   = (unsigned)((tcfg & EXMC_SNTCFG_AHLD) >> 4) + 1U;
      const unsigned dset   = (unsigned)((tcfg & EXMC_SNTCFG_DSET) >> 8) + 1U;
      const unsigned buslat = (unsigned)((tcfg & EXMC_SNTCFG_BUSLAT) >> 16) + 1U;
      ECAT_LOGI("[ECAT][EXMC] init: SNTCFG0=0x%08lX -> ASET=%u AHLD=%u DSET=%u BUSLAT=%u\r\n",
                (unsigned long)tcfg, aset, ahld, dset, buslat);
      /* 5 HCLK @180MHz = 27.8ns,DS trdrd 下限 13ns → 需 BUSLAT>=2 才达标,取 4 留余量 */
      if (buslat < 4U) {
        ECAT_LOGI("[ECAT][EXMC] WARN: BUSLAT=%u < 4, trdrd 余量不足,"
                  " 温漂/压降时会偶发读到 0xFFFF 或错值\r\n", buslat);
      }
    }

    /* 总线探活:LAN9252 处于 16-bit HBI Indexed Mode,无法通过固定偏移直接读取。
   * 真实的芯片 ID / AL 状态校验由 EscLan9252::init() 通过 HBI_IDX_0/HBI_DATA_0
   * 间接访问完成。 注意:LAN9252 上电后第一次 Host Bus
   * 操作必须是读周期,否则后续写操作会被忽略; EscLan9252 在 init 中首先读取
   * CHIP_ID,满足该约束。 */
  ECAT_LOGI("[ECAT][EXMC] init: Region0 enabled, chip ID will be verified by "
            "ESC driver\r\n");

  /* ---- 硬件诊断: 转储关键寄存器 + GPIO 手动输出测试 ----
   * 默认关闭。硬件层已确认全通,探针仅换板/补焊排查浮空时经
   * CONFIG_ESC_EXMC_DIAG 临时开启(会拆 EXMC 引脚成 GPIO,正常运行不该跑)。 */
#if CONFIG_ESC_EXMC_DIAG
  diagDump();
#endif

  s_ok = true;
  ECAT_LOGI("[ECAT][EXMC] init: OK, bus enabled\r\n");
  return true;
}

/* ========================================================================
 * 硬件诊断: 精简版 —— 只保留核心探活 + bit-bang + 位级回显
 * 整段由 CONFIG_ESC_EXMC_DIAG 门控,默认不编译。bbDelay/bbReadData/
 * bbDriveData 等位拍辅助函数在上方匿名 namespace 中,continuityDrive 仍复用,保留。
 * ======================================================================== */
#if CONFIG_ESC_EXMC_DIAG
void EscExmcBus::diagDump() {
  /* EtherCAT 同步 ISR 激活期间禁止诊断:本函数会把 EXMC 数据/控制线切成 GPIO,
   * 并大量 printf,会周期性拆毁运行中的 EtherCAT 总线。 */
  if (EthercatSync::isActive()) {
    printf("[EXMC-DIAG] skipped: EtherCAT sync ISR active (bus in use)\r\n");
    return;
  }
  /* 通断测试模式活跃时跳过诊断,避免 20s 周期 probe 覆盖用户设置的电平 */
  if (s_continuityActive) {
    printf("[EXMC-DIAG] skipped: continuity test mode active\r\n");
    return;
  }
  printf("[EXMC-DIAG] --- bit-bang probe (bypass EXMC) ---\r\n");
  /* NRST 实际电平回读:输入通路常连引脚,输出态亦读真实电压。
   * 驱动高却 LOW => ECAT_NRST 被外部按低 => LAN9252 一直在复位态。 */
  printf("[EXMC-DIAG] NRST(PB10) reads %s\r\n",
         (gpio_input_bit_get(CONFIG_ESC_NRST_PORT, CONFIG_ESC_NRST_PIN) == SET)
             ? "HIGH" : "LOW");

  /* 保存原 GPIO 配置 */
  uint32_t save_ctl0_d = GPIO_CTL0(GPIOD);
  uint32_t save_ctl1_d = GPIO_CTL1(GPIOD);
  uint32_t save_ctl0_e = GPIO_CTL0(GPIOE);
  uint32_t save_ctl1_e = GPIO_CTL1(GPIOE);

  /* 控制线 OUT_PP, 数据线 IN */
  gpio_init(GPIOD, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ,
            GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_7|GPIO_PIN_11|GPIO_PIN_12);
  gpio_init(GPIOD, GPIO_MODE_IN_FLOATING, 0, GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_8|
            GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_14|GPIO_PIN_15);
  gpio_init(GPIOE, GPIO_MODE_IN_FLOATING, 0, GPIO_PIN_7|GPIO_PIN_8|GPIO_PIN_9|
            GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12|GPIO_PIN_13|GPIO_PIN_14|GPIO_PIN_15);

  /* 空闲:CS/RD/WR 高, A1=A2=0 */
  GPIO_BOP(GPIOD) = (1U<<7)|(1U<<4)|(1U<<5);
  GPIO_BC(GPIOD) = (1U<<11)|(1U<<12);
  bbDelay();

  /* 读 IDX_0 (A2=0) —— 复位默认值 0x1234 */
  GPIO_BC(GPIOD) = (1U<<7);   /* CS=低 */
  bbDelay();
  GPIO_BC(GPIOD) = (1U<<4);   /* RD=低 */
  bbDelay();
  uint16_t bb_idx0 = bbReadData();
  GPIO_BOP(GPIOD) = (1U<<4);  /* RD=高 */
  bbDelay();
  GPIO_BOP(GPIOD) = (1U<<7);  /* CS=高 */
  bbDelay();

  printf("[EXMC-DIAG] bit-bang IDX_0 = 0x%04X (expect 0x1234)\r\n",
         (unsigned)bb_idx0);

  /* 判读 */
  if (bb_idx0 == 0x1234U) {
    printf("[EXMC-DIAG] *** LAN9252 ALIVE ***\r\n");
  } else if (bb_idx0 == 0x0000U || bb_idx0 == 0xFFFFU) {
    printf("[EXMC-DIAG] FAIL: bus floating (0x%04X) -> data line broken or chip not driving\r\n",
           (unsigned)bb_idx0);
  } else {
    printf("[EXMC-DIAG] UNEXPECTED: 0x%04X -> partial data line issue?\r\n",
           (unsigned)bb_idx0);
  }

  /* --- 预驱动/释放/读周期三段采样: 区分"被动拉低"与"芯片主动驱动" ---
   * 背景: bit-bang 读到稳定 0x0000, 而纯浮空输入应保持上次残留值或漂移。
   * 两种解释: (a) 板上下拉/对地漏电(被动) (b) 芯片在 RD# 有效期驱动 0(主动)。
   * 序列: 驱动 pattern -> 切输入快采样(电容应保持) -> 慢采样(检测下拉)
   *       -> 拉低 CS#+RD# 采样(芯片若响应应驱动总线, 例如 0x1234)。 */
  printf("[EXMC-DIAG] --- predrive/release/read probe ---\r\n");
  static const uint16_t probe_pats[2] = {0xAAAAU, 0x5555U};
  for (int p = 0; p < 2; ++p) {
    uint16_t pat = probe_pats[p];
    /* 1) 数据线推挽驱动 pattern(控制线保持空闲: CS/RD/WR 高, A1/A2 低) */
    gpio_init(GPIOD, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, kDataMaskD);
    gpio_init(GPIOE, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, kDataMaskE);
    bbDriveData(pat);
    bbDelay();
    /* 2) 切浮空输入, 快采样(自身电容应保持 pattern) */
    gpio_init(GPIOD, GPIO_MODE_IN_FLOATING, 0, kDataMaskD);
    gpio_init(GPIOE, GPIO_MODE_IN_FLOATING, 0, kDataMaskE);
    for (volatile int d = 0; d < 50; d++) {} /* ~微秒级 */
    uint16_t s_fast = bbReadData();
    /* 3) 慢采样(约 40-80us 后: 若板上有下拉会漏向 0) */
    bbDelay();
    uint16_t s_slow = bbReadData();
    /* 4) 读周期采样(CS#+RD# 低: 芯片若驱动会在总线上给出真实数据) */
    GPIO_BC(GPIOD) = (1U << 7) | (1U << 4);
    bbDelay();
    uint16_t s_rd = bbReadData();
    GPIO_BOP(GPIOD) = (1U << 4) | (1U << 7);
    bbDelay();
    printf("[EXMC-DIAG] pat=0x%04X fast=0x%04X slow=0x%04X rd=0x%04X\r\n",
           (unsigned)pat, (unsigned)s_fast, (unsigned)s_slow,
           (unsigned)s_rd);
  }

  /* 恢复 GPIO */
  GPIO_CTL0(GPIOD) = save_ctl0_d;
  GPIO_CTL1(GPIOD) = save_ctl1_d;
  GPIO_CTL0(GPIOE) = save_ctl0_e;
  GPIO_CTL1(GPIOE) = save_ctl1_e;

  /* EXMC 寄存器回读（一行） */
  printf("[EXMC-DIAG] SNCTL0=0x%08lX SNTCFG0=0x%08lX\r\n",
         (unsigned long)EXMC_SNCTL0, (unsigned long)EXMC_SNTCFG0);

  /* EXMC raw 读 + 位级回显（仅在未响应时） */
  uint16_t idx0_raw = ESC_EXMC_REG16(0x00000);
  printf("[EXMC-DIAG] EXMC raw IDX_0 = 0x%04X\r\n", (unsigned)idx0_raw);

  if (idx0_raw != 0x1234U) {
    /* 位级回显: 写 4 个 pattern 看哪些位回显(浮空)哪些位被驱动 */
    const uint16_t patterns[4] = {0x0000U, 0xFFFFU, 0xAAAAU, 0x5555U};
    uint16_t readbacks[4] = {0};
    for (int i = 0; i < 4; ++i) {
      ESC_EXMC_REG16(0x00000) = patterns[i];
      for (volatile int d = 0; d < 50; d++) {}
      readbacks[i] = ESC_EXMC_REG16(0x00000);
    }
    uint16_t echo_bits = 0U, driven_bits = 0U;
    for (int b = 0; b < 16; ++b) {
      uint16_t mask = (uint16_t)(1U << b);
      bool all_echo = true;
      for (int i = 0; i < 4; ++i) {
        if ((readbacks[i] & mask) != (patterns[i] & mask)) { all_echo = false; break; }
      }
      if (all_echo) echo_bits |= mask; else driven_bits |= mask;
    }
    printf("[EXMC-DIAG] echo bits(disconnected): 0x%04X  driven bits(connected): 0x%04X\r\n",
           (unsigned)echo_bits, (unsigned)driven_bits);

    if (echo_bits == 0xFFFFU) {
      printf("[EXMC-DIAG] ALL 16 bits floating -> CS not reaching LAN9252 or chip dead\r\n");
      printf("[EXMC-DIAG] -> run continuityTest() to check data lines with multimeter\r\n");
    } else if (driven_bits == 0xFFFFU) {
      printf("[EXMC-DIAG] ALL 16 bits driven -> HBI alive but IDX_0!=0x1234 (unexpected)\r\n");
    } else {
      printf("[EXMC-DIAG] PARTIAL echo -> broken data lines: ");
      for (int b = 0; b < 16; ++b) if (echo_bits & (1U << b)) printf("D%d ", b);
      printf("\r\n");
    }
  } else {
    printf("[EXMC-DIAG] === HBI ALIVE ===\r\n");
  }
}
#endif /* CONFIG_ESC_EXMC_DIAG */

/* ========================================================================
 * 通断测试: 网页逐个 pattern 触发,GD32 驱动数据线/控制线输出已知电平,
 *           用户用万用表在 LAN9252 端测量对应引脚电压。
 * 设计:
 *   - continuityDrive(action) 不延时,驱动完立即返回,电平保持到下次调用
 *   - action=0(stop) 恢复 GPIO 为 EXMC AF_PP,回到正常工作模式
 *   - 不点按钮时引脚是高阻输入态(安全),手碰到也不短路
 * 判据:
 *   - GD32 输出高(3.3V)但 LAN9252 端测到 0V/浮空 → 断线
 *   - GD32 输出低(0V)但 LAN9252 端测到 3.3V → 断线/短路
 *   - 电压跟随 → 连线正常
 * ======================================================================== */

static uint32_t s_save_ctl0_d = 0, s_save_ctl1_d = 0;
static uint32_t s_save_ctl0_e = 0, s_save_ctl1_e = 0;
static uint32_t s_maskPrev = 0U;

static void continuityEnterTestMode() {
  if (s_continuityActive) return;
  s_save_ctl0_d = GPIO_CTL0(GPIOD);
  s_save_ctl1_d = GPIO_CTL1(GPIOD);
  s_save_ctl0_e = GPIO_CTL0(GPIOE);
  s_save_ctl1_e = GPIO_CTL1(GPIOE);
  /* 测试期屏蔽 SYNC0/ESC IRQ/SYNC1:ISR 的 HBI 访问落在已被切成 GPIO 态的
   * 总线上只会读回垃圾并错写 IDX,SSC 状态可能被污染。 */
  s_maskPrev = EscExmcBus::maskEnter();
  /* 全部数据线 + 控制线设为 OUT_PP */
  gpio_init(GPIOD, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ,
            kDataMaskD | (1U<<kPinCs) | (1U<<kPinRd) | (1U<<kPinWr) |
            (1U<<kPinA1) | (1U<<kPinA2));
  gpio_init(GPIOE, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, kDataMaskE);
  /* 控制线空闲态: CS/RD/WR=高, A1=A2=低 */
  GPIO_BOP(GPIOD) = (1U<<kPinCs) | (1U<<kPinRd) | (1U<<kPinWr);
  GPIO_BC(GPIOD) = (1U<<kPinA1) | (1U<<kPinA2);
  s_continuityActive = true;
  printf("[CONT] test mode entered (GPIO -> OUT_PP, ECAT ISRs masked)\r\n");
}

static void continuityExitTestMode() {
  if (!s_continuityActive) return;
  GPIO_CTL0(GPIOD) = s_save_ctl0_d;
  GPIO_CTL1(GPIOD) = s_save_ctl1_d;
  GPIO_CTL0(GPIOE) = s_save_ctl0_e;
  GPIO_CTL1(GPIOE) = s_save_ctl1_e;
  EscExmcBus::maskExit(s_maskPrev);
  s_continuityActive = false;
  printf("[CONT] test mode exited (GPIO -> AF_PP restored, ISRs unmasked)\r\n");
}

uint8_t EscExmcBus::continuityDrive(uint8_t action) {
  switch (action) {
    case 0: /* stop */
      continuityExitTestMode();
      return 0;
    case 1: /* 0xFFFF ALL HIGH */
    case 2: /* 0x0000 ALL LOW */
    case 3: /* 0xAAAA ODD HIGH */
    case 4: { /* 0x5555 EVEN HIGH */
      continuityEnterTestMode();
      static const uint16_t pats[4] = {0xFFFF, 0x0000, 0xAAAA, 0x5555};
      uint16_t pat = pats[action - 1];
      bbDriveData(pat);
      /* 控制线恢复空闲态(避免上次控制线测试残留) */
      GPIO_BOP(GPIOD) = (1U<<kPinCs) | (1U<<kPinRd) | (1U<<kPinWr);
      GPIO_BC(GPIOD) = (1U<<kPinA1) | (1U<<kPinA2);
      printf("[CONT] pattern 0x%04X driven\r\n", (unsigned)pat);
      return 0;
    }
    case 5: /* CS low */
    case 6: /* RD low */
    case 7: /* WR low */
    case 8: /* A1 high */
    case 9: { /* A2 high */
      continuityEnterTestMode();
      /* 数据线恢复空闲(避免上次数据 pattern 残留) */
      bbDriveData(0x0000);
      uint32_t pin;
      bool drive_high;
      switch (action) {
        case 5: pin = kPinCs; drive_high = false; break; /* CS low */
        case 6: pin = kPinRd; drive_high = false; break; /* RD low */
        case 7: pin = kPinWr; drive_high = false; break; /* WR low */
        case 8: pin = kPinA1; drive_high = true;  break; /* A1 high */
        case 9: pin = kPinA2; drive_high = true;  break; /* A2 high */
        default: return 0xEE;
      }
      /* 先把所有控制线恢复空闲,再驱动目标线 */
      GPIO_BOP(GPIOD) = (1U<<kPinCs) | (1U<<kPinRd) | (1U<<kPinWr);
      GPIO_BC(GPIOD) = (1U<<kPinA1) | (1U<<kPinA2);
      if (drive_high) {
        GPIO_BOP(GPIOD) = (1U << pin);
      } else {
        GPIO_BC(GPIOD) = (1U << pin);
      }
      printf("[CONT] control line PD%lu driven %s\r\n",
             (unsigned long)pin, drive_high ? "HIGH" : "LOW");
      return 0;
    }
    case 10: { /* READ HOLD: CS#+RD# 持续拉低, 数据线浮空输入
      * 用途: 万用表在 LAN9252 芯片侧引脚测量读周期数据电平。
      * 判据: 芯片 HBI 活着 => 驱动 IDX_0=0x1234 (0001 0010 0011 0100b) =>
      *   置位 bit2/4/5/9/12 => D2(Pin12)/D4(Pin49)/D5(Pin50)/D9(Pin19)/
      *   D12(Pin21)=3.3V, 其余数据脚=0V(全部为确定电平)。
      * 全部中电平/漂移 => 芯片未驱动(区分"芯片不驱动"与"数据线断线":
      * GD32 侧 rd 采样无法区分两者, 芯片侧测量可以)。 */
      continuityEnterTestMode(); /* 幂等:已活跃则保持;内部已屏蔽 ECAT ISR */
      /* 数据线浮空输入(交给芯片驱动),控制线保持 OUT_PP */
      gpio_init(GPIOD, GPIO_MODE_IN_FLOATING, 0, kDataMaskD);
      gpio_init(GPIOE, GPIO_MODE_IN_FLOATING, 0, kDataMaskE);
      /* 持续读周期: WR 高, CS#+RD# 低, A1=A2=0 -> 读 IDX_0 */
      GPIO_BOP(GPIOD) = (1U<<kPinWr);
      GPIO_BC(GPIOD) = (1U<<kPinCs) | (1U<<kPinRd) | (1U<<kPinA1) | (1U<<kPinA2);
      printf("[CONT] READ-HOLD: CS#+RD# held low, data Hi-Z\r\n");
      printf("[CONT] measure at chip: D2(P12)/D4(P49)/D5(P50)/D9(P19)/D12(P21)=3.3V & others 0V => alive(0x1234); all floating => not driving\r\n");
      return 0;
    }
    default:
      return 0xEE;
  }
}

__attribute__((section(".ramfunc"), noinline)) uint16_t
EscExmcBus::read16(uint32_t offset) {
  return ESC_EXMC_REG16(offset);
}

__attribute__((section(".ramfunc"), noinline)) void
EscExmcBus::write16(uint32_t offset, uint16_t data) {
  ESC_EXMC_REG16(offset) = data;
}

uint32_t EscExmcBus::maskEnter() {
  uint32_t prev = 0U;
  /* EXTI0=SYNC0(preempt=0) 无法被 BASEPRI 屏蔽,只能关 NVIC;
   * EXTI1=ESC IRQ / EXTI2=SYNC1 (均 preempt=1) 的 PDI_Isr/Sync1_Isr 同样做
   * HBI 两步事务访问,一并屏蔽——否则主循环事务会被 Sync1_Isr 的
   * PDO_InputMapping→HW_EscWriteIsr 打断而错址。 */
  if (NVIC_GetEnableIRQ(EXTI0_IRQn) != 0U) {
    prev |= 1U;
    NVIC_DisableIRQ(EXTI0_IRQn);
  }
  if (NVIC_GetEnableIRQ(EXTI1_IRQn) != 0U) {
    prev |= 2U;
    NVIC_DisableIRQ(EXTI1_IRQn);
  }
  if (NVIC_GetEnableIRQ(EXTI2_IRQn) != 0U) {
    prev |= 4U;
    NVIC_DisableIRQ(EXTI2_IRQn);
  }
  return prev;
}

void EscExmcBus::maskExit(uint32_t prev) {
  /* 按保存的状态恢复:外层已屏蔽的(如 SSC DISABLE_ESC_INT)不会被误开 */
  if ((prev & 4U) != 0U) {
    NVIC_EnableIRQ(EXTI2_IRQn);
  }
  if ((prev & 2U) != 0U) {
    NVIC_EnableIRQ(EXTI1_IRQn);
  }
  if ((prev & 1U) != 0U) {
    NVIC_EnableIRQ(EXTI0_IRQn);
  }
}