cbb
db2d08032c
- 移除冗余的三值约束宏定义 `_constrain3` - 修改关机逻辑，引入 `thermal_uncontrol` 标志替代旧 shut_down 计数方式 - 调整恢复函数中错误标志位清零逻辑 - 将部分 uint8_t 类型成员变量改为 bool 类型以提高可读性 - 在类中添加电源电压成员变量并调整 PID 参数初始化 - 移除 PID 控制器中不必要的 CAN 测试代码 - 添加 thermal 控制相关文件引用及初始化 - 使用 switch 替代多重 if-else 提高控制模式处理效率 - 引入基于定时器的任务负载均衡调度机制 - 初始化热量控制器并在主循环中调用更新逻辑
398 lines
11 KiB
C++
398 lines
11 KiB
C++
#include "Timer.h"
|
|
#include "Can.h"
|
|
#include "DengFOC.h"
|
|
#include "Filter.h"
|
|
#include "Timer.h"
|
|
#include "adc.h"
|
|
#include "ang_sensor.h"
|
|
#include "gd32c10x.h"
|
|
#include "gd32c10x_gpio.h"
|
|
#include "gd32c10x_misc.h"
|
|
#include "gd32c10x_rcu.h"
|
|
#include "gd32c10x_timer.h"
|
|
#include "thermal.h"
|
|
#include <cstdio>
|
|
#include <stdbool.h>
|
|
#include <stdint.h>
|
|
#include <stdio.h>
|
|
|
|
constexpr int TIMER2_PRESCALER = 119; // 120MHz / 120 = 1MHz
|
|
constexpr int TIMER2_PERIOD = 99; // 1MHz / 100 = 100us
|
|
constexpr int TIMER3_PRESCALER = 119; // 120MHz / 120 = 1MHz
|
|
constexpr int TIMER3_PERIOD = 9999; // 1MHz / 10000 = 100Hz = 10ms
|
|
|
|
constexpr int TIMER1_PRESCALER = 0; // 不分频，计数器时钟为120MHz
|
|
constexpr int TIMER1_PERIOD = 5999; // 120MHz / (0+1) / (5999+1) = 20kHz
|
|
constexpr int TIMER1_CH0_PULSE = 0;
|
|
constexpr int TIMER1_CH1_PULSE = 0;
|
|
constexpr int TIMER1_CH2_PULSE = 0;
|
|
|
|
static u32 total_us100_counter = 0; // 总计数器，每100微秒增加1
|
|
extern u16 adc_value[7];
|
|
extern CAN_transmiter CAN0_transmiter;
|
|
// 添加系统运行时间计数器
|
|
static volatile std::u64 system_runtime_us = 0;
|
|
|
|
// 声明外部FOC控制器对象
|
|
extern FOC_Controlroller FOC;
|
|
// 声明外部采样器对象
|
|
extern sampler sampler;
|
|
extern angle_sensor KTH7823;
|
|
extern EncoderVelocityKalman Vel_kalman;
|
|
extern ThermalController thermalController; // 热量控制器初始化
|
|
|
|
/**
|
|
* @brief 设置引脚中断优先级
|
|
* @return void
|
|
*
|
|
*设置引脚中断优先级
|
|
*/
|
|
void nvic_config(void) {
|
|
/* 设置NVIC优先级分组，1位抢占优先级，3位响应优先级 */
|
|
nvic_priority_group_set(NVIC_PRIGROUP_PRE2_SUB2);
|
|
/* 使能TIMER2中断，设置抢占优先级为1，子优先级为1 */
|
|
nvic_irq_enable(TIMER2_IRQn, 1, 1);
|
|
nvic_irq_enable(TIMER3_IRQn, 1, 2);
|
|
}
|
|
|
|
/**
|
|
* @brief 配置定时器2
|
|
* @return void
|
|
*
|
|
*配置定时器2，用于定时执行FOC控制、采样、CAN发送等任务
|
|
*/
|
|
void TIMER2_config(void) {
|
|
/* ----------------------------------------------------------------------------
|
|
TIMER2 Configuration:
|
|
TIMER2CLK = SystemCoreClock/120 = 1MHz, the period is 100us(100/1000000 =
|
|
100us).
|
|
----------------------------------------------------------------------------
|
|
*/
|
|
timer_parameter_struct timer_struct;
|
|
|
|
/* 使能TIMER2时钟 */
|
|
rcu_periph_clock_enable(RCU_TIMER2);
|
|
|
|
/* 复位TIMER2外设到默认状态 */
|
|
timer_deinit(TIMER2);
|
|
/* 初始化TIMER初始化参数结构体 */
|
|
timer_struct_para_init(&timer_struct);
|
|
/* TIMER2配置参数设置 */
|
|
timer_struct.prescaler =
|
|
TIMER2_PRESCALER; /* 预分频值：120分频(从0开始计数) */
|
|
timer_struct.alignedmode = TIMER_COUNTER_EDGE; /* 边沿对齐模式 */
|
|
timer_struct.counterdirection = TIMER_COUNTER_UP; /* 向上计数模式 */
|
|
timer_struct.period =
|
|
TIMER2_PERIOD; /* 自动重装载值：100次计数(从0开始计数) */
|
|
timer_struct.clockdivision = TIMER_CKDIV_DIV1; /* 时钟分频值：1分频 */
|
|
timer_init(TIMER2, &timer_struct);
|
|
|
|
/* 清除更新中断标志位 */
|
|
timer_interrupt_flag_clear(TIMER2, TIMER_INT_FLAG_UP);
|
|
/* 使能更新中断 */
|
|
timer_interrupt_enable(TIMER2, TIMER_INT_UP);
|
|
|
|
/* 使能TIMER2 */
|
|
timer_enable(TIMER2);
|
|
}
|
|
|
|
/**
|
|
* @brief 配置定时器3
|
|
* @return void
|
|
*
|
|
*配置定时器3，用于诊断恢复
|
|
*/
|
|
void TIMER3_config(void) {
|
|
/* ----------------------------------------------------------------------------
|
|
TIMER3 Configuration:
|
|
TIMER3CLK = SystemCoreClock/120 = 1MHz, the period is 10ms(10000/1000000 =
|
|
10ms).
|
|
----------------------------------------------------------------------------
|
|
*/
|
|
timer_parameter_struct timer_struct;
|
|
|
|
/* 使能TIMER3时钟 */
|
|
rcu_periph_clock_enable(RCU_TIMER3);
|
|
|
|
/* 复位TIMER3外设到默认状态 */
|
|
timer_deinit(TIMER3);
|
|
/* 初始化TIMER初始化参数结构体 */
|
|
timer_struct_para_init(&timer_struct);
|
|
/* TIMER3配置参数设置 */
|
|
timer_struct.prescaler =
|
|
TIMER3_PRESCALER; /* 预分频值：120分频(从0开始计数) */
|
|
timer_struct.alignedmode = TIMER_COUNTER_EDGE; /* 边沿对齐模式 */
|
|
timer_struct.counterdirection = TIMER_COUNTER_UP; /* 向上计数模式 */
|
|
timer_struct.period =
|
|
TIMER3_PERIOD; /* 自动重装载值：10000次计数(从0开始计数) */
|
|
timer_struct.clockdivision = TIMER_CKDIV_DIV1; /* 时钟分频值：1分频 */
|
|
timer_init(TIMER3, &timer_struct);
|
|
|
|
/* 清除更新中断标志位 */
|
|
timer_interrupt_flag_clear(TIMER3, TIMER_INT_FLAG_UP);
|
|
/* 使能更新中断 */
|
|
timer_interrupt_enable(TIMER3, TIMER_INT_UP);
|
|
|
|
/* 使能TIMER3 */
|
|
timer_enable(TIMER3);
|
|
}
|
|
|
|
/**
|
|
* @brief 配置TIMER2中断
|
|
* @return void
|
|
*/
|
|
void User_timer_init(void) {
|
|
/* 配置TIMER2 */
|
|
TIMER2_config();
|
|
/* 配置TIMER2中断 */
|
|
nvic_config();
|
|
}
|
|
|
|
/*!
|
|
\brief 获取系统运行时间(毫秒)
|
|
\param[in] none
|
|
\param[out] none
|
|
\retval 系统运行时间，单位为毫秒
|
|
*/
|
|
uint64_t get_system_runtime_us(void) { return system_runtime_us; }
|
|
|
|
/**
|
|
* @brief TIMER2中断处理函数
|
|
* @return void
|
|
*/
|
|
void TIMER2_IRQHandler(void) {
|
|
static u8 mode = 0;
|
|
// 检查更新中断标志并处理
|
|
if (timer_interrupt_flag_get(TIMER2, TIMER_INT_UP) != RESET) {
|
|
// 清除更新中断标志
|
|
timer_interrupt_flag_clear(TIMER2, TIMER_INT_UP);
|
|
|
|
// 增加总计数器 (使用更高效的位运算代替取模运算)
|
|
total_us100_counter++;
|
|
// system_runtime_us += 100;
|
|
|
|
// 每100us执行一次的操作
|
|
sampler.update_current(); // 更新电流采样值
|
|
KTH7823.update(); // 更新角度传感器值
|
|
FOC.rt_velocity = Vel_kalman.update(KTH7823.getVelocity());
|
|
FOC.rt_angle = KTH7823.getAngle();
|
|
switch (FOC.control_mode) {
|
|
case 0: {
|
|
break;
|
|
}
|
|
case 1: {
|
|
FOC.angle_control(FOC.target_angle); // 角度闭环控制
|
|
break;
|
|
}
|
|
case 2: {
|
|
FOC.velocity_control(FOC.target_velocity); // 速度闭环控制
|
|
break;
|
|
}
|
|
case 3: {
|
|
FOC.angle_control_NPID(FOC.target_angle); // 角度闭环控制
|
|
break;
|
|
}
|
|
case 4: {
|
|
FOC.velocity_open_loop(); // 速度闭环控制
|
|
break;
|
|
}
|
|
}
|
|
switch (total_us100_counter) { // 每1ms执行的代码，负载均衡
|
|
case 1: {
|
|
// 设置CAN发送标志
|
|
CAN0_transmiter.can0_send_flag = SET;
|
|
mode = FOC.control_mode;
|
|
break;
|
|
}
|
|
case 2: {
|
|
sampler.update_mcu_temp();
|
|
break;
|
|
}
|
|
case 3: {
|
|
sampler.update_drv_temp();
|
|
break;
|
|
}
|
|
case 4: {
|
|
sampler.update_vbus_voltage();
|
|
break;
|
|
}
|
|
}
|
|
if (total_us100_counter >= 10) {
|
|
total_us100_counter = 0;
|
|
// 可以添加每1ms执行的代码，无负载均衡
|
|
static u8 ms10_counter = 0;
|
|
ms10_counter++;
|
|
switch (ms10_counter) { // 每10ms执行的代码，负载均衡
|
|
case 1: {
|
|
FOC.update_power();
|
|
break;
|
|
}
|
|
case 2: {
|
|
thermalController.update();
|
|
break;
|
|
}
|
|
}
|
|
if (ms10_counter >= 10) {
|
|
ms10_counter = 0;
|
|
// 可以添加每10ms执行的代码，无负载均衡
|
|
static u8 ms100_counter = 0;
|
|
ms100_counter++;
|
|
switch (ms100_counter) { // 每100ms执行的代码，负载均衡
|
|
case 1: {
|
|
break;
|
|
}
|
|
if (ms100_counter >= 10) {
|
|
ms100_counter = 0;
|
|
// 可以添加每100ms执行的代码
|
|
|
|
static u8 sec_counter = 0;
|
|
sec_counter++;
|
|
if (sec_counter >= 10) {
|
|
sec_counter = 0;
|
|
// 可以添加每1s执行的代码
|
|
}
|
|
}
|
|
}
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief TIMER3中断处理函数
|
|
* @return void
|
|
*/
|
|
void TIMER3_IRQHandler(void) {
|
|
// 检查更新中断标志并处理
|
|
if (timer_interrupt_flag_get(TIMER3, TIMER_INT_UP) != RESET) {
|
|
// 清除更新中断标志
|
|
timer_interrupt_flag_clear(TIMER3, TIMER_INT_UP);
|
|
static u8 count = 0;
|
|
count++;
|
|
|
|
// 10ms测试代码
|
|
if (count >= 10) {
|
|
count = 0;
|
|
// 100ms测试代码
|
|
|
|
static u8 count_10 = 0;
|
|
count_10++;
|
|
if (count_10 >= 10) {
|
|
count_10 = 0;
|
|
// 1s测试代码
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief TIMER1 GPIO配置函数
|
|
*/
|
|
void timer1_gpio_config(void) {
|
|
// 时钟使能
|
|
rcu_periph_clock_enable(RCU_GPIOA);
|
|
rcu_periph_clock_enable(RCU_GPIOB);
|
|
rcu_periph_clock_enable(RCU_AF);
|
|
rcu_periph_clock_enable(RCU_TIMER1);
|
|
|
|
// TIMER1 GPIO初始化
|
|
gpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_0);
|
|
gpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_1);
|
|
gpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_2);
|
|
|
|
gpio_init(GPIOB, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ,
|
|
GPIO_PIN_0 | GPIO_PIN_12);
|
|
gpio_bit_set(GPIOB, GPIO_PIN_0);
|
|
gpio_bit_set(GPIOB, GPIO_PIN_12);
|
|
|
|
/* 配置TIMER1完全重映射 - 应该使用DISABLE，因为我们使用的是默认引脚 */
|
|
gpio_pin_remap_config(GPIO_TIMER1_FULL_REMAP, DISABLE);
|
|
}
|
|
|
|
/**
|
|
* @brief TIMER1 配置函数
|
|
*/
|
|
void timer1_pwm_config(void) {
|
|
timer_parameter_struct timer_initpara;
|
|
timer_oc_parameter_struct timer_ocinitpara;
|
|
|
|
// 使能TIMER1时钟
|
|
rcu_periph_clock_enable(RCU_TIMER1);
|
|
|
|
// 复位TIMER1
|
|
timer_deinit(TIMER1);
|
|
|
|
// 配置TIMER1基本参数
|
|
timer_struct_para_init(&timer_initpara);
|
|
timer_initpara.prescaler = TIMER1_PRESCALER; // 预分频器
|
|
timer_initpara.counterdirection = TIMER_COUNTER_UP; // 向上计数
|
|
timer_initpara.period = TIMER1_PERIOD; // 计数周期
|
|
timer_initpara.clockdivision = TIMER_CKDIV_DIV1;
|
|
timer_init(TIMER1, &timer_initpara);
|
|
|
|
// 配置通道输出参数
|
|
timer_channel_output_struct_para_init(&timer_ocinitpara);
|
|
timer_ocinitpara.outputstate = TIMER_CCX_ENABLE;
|
|
timer_ocinitpara.ocpolarity = TIMER_OC_POLARITY_HIGH;
|
|
|
|
// 配置三个通道为PWM模式
|
|
timer_channel_output_config(TIMER1, TIMER_CH_0, &timer_ocinitpara);
|
|
timer_channel_output_config(TIMER1, TIMER_CH_1, &timer_ocinitpara);
|
|
timer_channel_output_config(TIMER1, TIMER_CH_2, &timer_ocinitpara);
|
|
|
|
// 设置PWM模式和占空比
|
|
timer_channel_output_mode_config(TIMER1, TIMER_CH_0, TIMER_OC_MODE_PWM0);
|
|
timer_channel_output_mode_config(TIMER1, TIMER_CH_1, TIMER_OC_MODE_PWM0);
|
|
timer_channel_output_mode_config(TIMER1, TIMER_CH_2, TIMER_OC_MODE_PWM0);
|
|
|
|
timer_channel_output_pulse_value_config(TIMER1, TIMER_CH_0,
|
|
TIMER1_CH0_PULSE);
|
|
timer_channel_output_pulse_value_config(TIMER1, TIMER_CH_1,
|
|
TIMER1_CH1_PULSE);
|
|
timer_channel_output_pulse_value_config(TIMER1, TIMER_CH_2,
|
|
TIMER1_CH2_PULSE);
|
|
|
|
// 使能主输出和自动重载
|
|
timer_primary_output_config(TIMER1, ENABLE);
|
|
timer_auto_reload_shadow_enable(TIMER1);
|
|
|
|
// 启动TIMER1
|
|
timer_enable(TIMER1);
|
|
}
|
|
|
|
/*!
|
|
\brief set PWM
|
|
\param[in] channel: TIMER_CH_0/TIMER_CH_1/TIMER_CH_2/TIMER_CH_3 (valid
|
|
values: 0, 1, 2, 3)
|
|
\param[in] pulse: PWM pulse value
|
|
\param[out] none
|
|
\retval none
|
|
\note The channel parameter must be between 0 and 3 inclusive.
|
|
*/
|
|
void Set_Pwm(u16 channel, float duty_cycle) {
|
|
float pulse = duty_cycle * TIMER1_PERIOD;
|
|
|
|
if (channel <= 3) {
|
|
timer_channel_output_pulse_value_config(TIMER1, channel, pulse);
|
|
} else {
|
|
} // Ensure channel is within valid range
|
|
}
|
|
|
|
/*!
|
|
\brief set PWM
|
|
\param[in] channel: TIMER_CH_0/TIMER_CH_1/TIMER_CH_2/TIMER_CH_3 (valid
|
|
values: 0, 1, 2, 3)
|
|
\param[in] pulse: PWM pulse value
|
|
\param[out] none
|
|
\retval none
|
|
\note The channel parameter must be between 0 and 3 inclusive.
|
|
*/
|
|
void Set_3Pwm(float duty_cycle0, float duty_cycle1, float duty_cycle2) {
|
|
timer_channel_output_pulse_value_config(TIMER1, TIMER_CH_0,
|
|
duty_cycle0 * TIMER1_PERIOD);
|
|
timer_channel_output_pulse_value_config(TIMER1, TIMER_CH_1,
|
|
duty_cycle1 * TIMER1_PERIOD);
|
|
timer_channel_output_pulse_value_config(TIMER1, TIMER_CH_2,
|
|
duty_cycle2 * TIMER1_PERIOD);
|
|
}
|